Penguin Pumps by Filter Pump Industries

Filter Pump Industries - Penguin Pump

CDI Equipment Division logo

Equipment Overview  |  Filter Pump Industries / Penguin Pump  |  Process Technology

Filter Pump Industries - a division of Penguin Pumps, Incorporated.

 

Pumps

Series P Sealless Vertical Pumps

P Series Header P Series Pump

Penguin sealless vertical pumps are designed to handle a wide range of chemicals without difficulty. Completely constructed of CPVC, polypropylene, or PVDF where in contact with the solution being pumped, Series P pumps have an upper working temperature of 180/150/280° F, respectively, and thus can handle most corrosive, slurries, and abrasive solutions. Series P pumps are easy to install and operate. They have no seals or bushings, can run dry, and are virtually maintenance-free.

Features and Benefits:

  • Choice of CPVC, PVDF, or Polypropylene
  • Runs dry without damage
  • Self-priming when immersed
  • No metal contact
  • Chemical-resistant

Bulletins (PDF):

Series PHF High Flow Vertical Pumps

PHF Series Pump

Penguin Series P-HF CPVC vertical pumps are simple in design, efficient in performance, and self-priming when immersed in solution. With a double impeller design and no seals to leak or bushings or bearings to wear, this pump can run dry without damage while requiring little or no maintenance.

Features and Benefits:

  • CPVC Construction
  • Optional PVDF Impeller available
  • No metal contact
  • Chemical resistant
  • Self-priming when immersed
  • Dry run capability without damage

Bulletins (PDF):

Series HV Horizontal Centrifugal Pumps

HV Series Header HV Series Pump

Penguin horizontal centrifugal pumps are designed to handle a wide range of chemicals without difficulty. Completely constructed of CPVC where in contact with the solution being pumped, Series HV pumps have an upper working temperature of 180° F, and thus can handle most corrosive, slurries, and abrasive solutions. For high temperatures and very corrosive abrasive solutions, a double mechanical seal and water flush are supplied. For higher suction pressure, a single diplo internal seal is supplied.

Features and Benefits:

  • Tru Volute design
  • High efficiency
  • Energy Saving
  • Higher flow vs. pressure
  • No metal contact

Bulletins (PDF):

Series M Magnetic-Drive Pumps

M Series Header M Series Pump

Penguin magnetic-driven pumps are designed to handle a wide range of chemicals without difficulty. Constructed of polypropylene, kynar, or stainless steel, Series M pumps have an upper working temperature of 190/220/250° F, respectively, and thus can handle highly corrosive or mild chemicals, acids, or solvents. Series M pumps eliminate the conventional shaft seal found in most pumps. This means that there is no rotating seal to wear out and allow the liquid being pumped to leak out. The pumping action may eventually fail, however, the liquid can never leak out. Series M pumps are easy to install and operate, and are virtually maintenance-free.

Features and Benefits:

  • Sealless
  • No metal contact
  • Bearing-free
  • Chemical resistant
  • Leak resistant
  • Available in 316SS, Kynar, and Hastelloy

Bulletins (PDF):

Series V Self-Priming Sealless Pumps

V Series Header V Series Pump

Penguin self-priming sealless pumps offer the utmost in reliability, versatility, constant operating conditions, long working life, and practically maintenance-free operation. The only pump element subjected to natural wear is the flexible liner which, as with all other parts of the pump, can be easily replaced without the use of special tools. Series V pumps can be supplied with either a viton or neoprene liner, thus providing a pump which is resistant to most aggressive media such as the delivery of alkalines or acidiferous fluids, solvents, water of all grades of purity, waste water of all kinds, miscellaneous pharmaceuticals, galvanic fluids, solutions for the photo and film industry, fluids for the beverage and food industry, media for paper, textile and leather treatment, as well as paint and other coating media.

Features and Benefits:

  • Wet or Dry operation
  • No gasketst
  • No shaft-seals
  • Self-priming

Series HD Multi-stage Horizontal Pumps

HD Series Header HD Series Pump

Penguin multi-stage horizontal diffuser pumps are designed for higher pressure applications where a metallic pump is unacceptable. Constructed of CPVC, a 316SS shaft, and a metalless diplo seal, Series HD pumps are designed to handle a wide range of semi-corrosive chemicals without difficulty. An optional titanium shaft can be supplied for more corrosive solutions with an upper working temperature of 180° F.

Features and Benefits:

  • Corrosion-resistant
  • Optimum Efficiency
  • Choice of three HP
  • High pressure, utilizing smaller pump cases
  • Diplo springless seal

Bulletins (PDF):

Series PB/PE/PEP Electronic Metering Pumps

PB/PE/PEP Series Header PB/PE/PEP Series Pump

Penguin electronic metering pumps are positive displacement, non-hydraulic, solenoid driven, diaphragm type pumps. In the Series PB/PE/PEP pumps, the electronic circuitry is EMI resistant, incorporates automatic reset thermal overload protection, and employs a MOV for lightning protection. Pump drives are encased in water and chemical resistant housings. Most models are UL listed for outdoor and indoor applications and are CSA and NSF approved.

Features and Benefits:

  • Series PB:
    • Lowest cost alternative
    • Manual function controls for stroke rate and length
  • Series PE:
    • Highly accurate digital timing circuit
    • Thermally protected solenoid with auto-reset
  • Series PEP:
    • Panel mounted circuit breaker

Series HSC 316SS Horizontal Centrifugal Pumps

HSC Series Header HSC Series Pump

Penguin 316 stainless steel centrifugal pumps are designed to handle a wide range of acids and alkalies as well as solvents to 250° F. For most conditions in the Series HSC pumps, the mechanical seal is cooled and lubricated by the liquid being pumped. Standard seals are supplied for suction pressures between 20 inches Hg vacuum and 85 psig, and liquid temperatures between -30° F and 211° F. Temperatures greater than 211° F, but less than 250° F, are acceptable for non-caustic, non-hydrocarbon service, but an optional seal assembly must be utilized.

Features and Benefits:

  • Chemical-resistant
  • Simplicity of Design
  • High Operational Efficiency
  • Easy maintenance
  • Double seal with water flush
  • Multi-Stage

Bulletins (PDF):

Series HOM Polypropylene Horizontal Centrifugal Pumps

HOM Series Header HOM Series Pump

Penguin horizontal centrifugal pumps are designed to handle a wide range of semi-corrosive chemicals with little or no difficulty. Constructed of glass-filled polypropylene with a CPVC impeller in contact with the solution, Series HOM pumps have an upper working temperature of 150° F, and thus can handle many general industrial applications. A metalless internal diplo seal is supplied to allow for higher suction pressures.

Features and Benefits:

  • Corrosion-resistant
  • Optimum Efficiency
  • Diplo Springless Seal
  • Choice of 5 HP
  • High Flow Rates

Bulletins (PDF):

Series HN Horizontal Volute Pumps

HN Series Header HN Series Pump

Penguin horizontal volute pumps are designed for larger volume than the Series HV and are able to handle a wide range of chemicals without difficulty. Completely constructed of CPVC where in contact with the solution being pumped, Series HN pumps have an upper working temperature of 180º F, and thus can handle most corrosive, slurries, and abrasive solutions. For high temperatures and very corrosive abrasive solutions, a double mechanical seal and water flush are supplied.

Features and Benefits:

  • Corrosion resistant
  • Very high efficiency
  • True volute design with center discharge
  • No metal contact
  • High flow rates

Series MT High Volume Sealless Magnetic-Drive Pumps

MT Series Header MT Series Pump

Penguin magnetic-driven pumps are designed for larger volume than the Series M and are able to handle a wide range of chemicals without difficulty. Constructed of polypropylene or PVDF, Series MT pumps have an upper working temperature of 180/220º F, respectively, and thus can handle highly corrosive or mild chemicals, acids, or solvents. Series MT pumps eliminate the conventional shaft seals found in most pumps. This means that there is no rotating seal to wear and allow the liquid being pumped to leak out. The pumping action may eventually fail, however, the liquid can never leak out. Series MT pumps are easy to install and operate, and are virtually maintenance-free.

Features and Benefits:

  • Chemical-resistant
  • Leak-resistant and sealless
  • Rugged catilever design
  • Runs dry to 30 minutes

Bulletins (PDF):

Series PX Extended Vertical Sealless Pumps

PX Series Header PX Series Pump

Penguin extended vertical immersible pumps are simple in design, efficient in performance, and self-priming when immersed in solution. Constructed completely of CPVC with glass molybdenum filled PTFE wear ring, or CPVC with PVDF impeller where in contact with the solution, this pump is suitable for pumping, agitating, filtering, or circulating acid and alkaline solutions, abrasive fluids, and other corrosive solutions up to 180° F maximum temperature. Penguin vertical pumps are versatile, easy to install, and require a minimal amount of tank space, thus saving valuable floor space.

Features and Benefits:

  • CPVC Construction
  • Optional PVDF Impeller available
  • No metal contact
  • Self-priming when immersed
  • Dry run capability with PVDF impeller

Bulletins (PDF):